1 Series

1. Device Overview

The Daavlin 1 Series is a home phototherapy device available with two controller options: ClearLink™ (touchscreen) and Digital Timer (DT). Both support 0 in and 9 in treatment distances and are prescribed and supervised by a physician.

2. Controller Types (ClearLink vs. DT)

3. Indications for Use

For the treatment of diagnosed skin disorders such as psoriasis, vitiligo, and atopic dermatitis (eczema) under physician direction. Suitable from pediatric through geriatric populations.

4. Warnings & Safety

• Prescription Use Only. Treatments must be supervised by a licensed physician.
• Always wear UV‑blocking goggles for anyone in view of the device.
• Protect untreated skin (e.g., sunscreen SPF 30+ on areas not being treated).
• Do not treat over burns/eruptions or if experiencing unresolved erythema.
• Typical thermal duty cycle: ~10 minutes on / 10 minutes off for very long sessions.
• Keep people and pets out of the treatment area. Avoid water and damaged cords.

5. Setup & Assembly

1. Site: Dry, ventilated area; near grounded outlet; away from traffic/water.
2. Unpack: Remove device and accessories. Connect the “D”-shaped power plug, then plug into a grounded outlet.
3. Optional: Install swivel stand per its instructions (if purchased).
4. Verify lamps: Confirm lamp type matches prescription (UVA, UVA‑1, NB‑UVB, BB‑UVB, Blue).

6. Positioning & Treatment Distance

Select one of two distances before treating:

• 0 in (on acrylic): Higher intensity; used for hands/feet resting on the guard.
• 9 in (23 cm): For larger areas with the device upright and body 9 in away.

Use the distance consistently with the prescription; switching distances changes treatment time.

7. Operating – ClearLink™

Guided Mode

1. Unlock device. The scheduled dose appears.
2. Answer “Were you in pain or red after your last treatment?” (Still red/pain locks the device until one session is skipped.)
3. Select distance: 0 in or 9 in.
4. Confirm dose & estimated time, put on goggles, position yourself, then Enter to start (3‑sec countdown).
5. Use Repeat to treat another area with the same dose before leaving the screen.

Dosimetric Mode

1. Unlock → Treat Patient → choose 0 in or 9 in.
2. Set prescribed dose (mJ for UVB; J for UVA as programmed).
3. Confirm, wear goggles, position, then Enter to begin. Integrating dosimetry auto‑adjusts time.
4. Pause/Play as needed; Repeat to expose another area before exiting.

Timed Mode

1. Unlock → Treat Patient → set time (mm:ss). Use 1:00 instead of 0:60.
2. Confirm, wear goggles, select distance, then Enter to begin.
3. Tip: For % increases, use Daavlin’s Treatment Time Calculator (see Downloads).

8. Operating – Digital Timer (DT)

1. Unlock with key code (see next section).
2. Display shows 00:00 with rightmost digit flashing.
3. Use ▲ to change the flashing digit; use ◀ to move left.
4. Press Play/Pause to lock in the time, then press again to start (pause/resume with the same key).
5. After completion, the controller flashes the last treatment in Standby; press Play/Pause twice to repeat.

Example: To enter 01:23 → ▲×3 → ◀ then ▲×2 → ◀ then ▲×1 → Play/Pause → Play/Pause.

9. Unlock Codes & Security

10. FlexRx® Prescriptions

11. Cleaning, Maintenance & Lamps

Routine Care

• Clean patient-contact surfaces between each treatment.
• Dust unit and lamps monthly; clean behind acrylic and reflectors annually.
• Replace lamps: UVB ~300 hrs; UVA/Blue ~500 hrs (environment dependent).

Cleaning & Disinfection

• General: Non‑abrasive cloth + mild soap (no paper towels on reflective surfaces).
• Low‑level: Monk™ wipes (per label) or 70% Isopropyl Alcohol (3 min contact).
• High‑level (between different patients): Use an FDA‑cleared high‑level disinfectant (e.g., Resert XL‑HLD) per manufacturer.

Lamp Replacement (summary)

1. Unplug. Remove two side screws; lift top cover.
2. Remove clear plastic clasps; press red socket button; lift lamp out with two hands.
3. Seat new lamps firmly (audible snap). Replace all lamps as a set; then reset lamp hours to 0.

Calibration (ClearLink Guided/Dosimetric)

Maintain calibration annually or every 100 hours and when lamps change; the integrating dosimeter targets ±5% timer accuracy and ±10% sensor accuracy.

12. Troubleshooting

• Lamps won't ignite: Confirm unlock, mode/time set, goggles on, and power; if still failing, contact support.
• Unexpected lock (“Still red/pain”): Skip one treatment to clear (Guided mode safety).
• Power loss mid‑treatment: ClearLink remembers elapsed time (lamps remain off until resumed). DT does not; restart per prescription.
• Overheating/discomfort: Use 10‑on/10‑off duty cycle for long sessions; allow cool‑down.
• FlexRx exhausted: Follow refill steps in Section 10.

13. Operating Specifications

• Ambient Temperature: 15–30°C (59–86°F)
• Relative Humidity: 10–95% (non‑condensing)
• Liquid Ingress: IPX0 (no water ingress protection)
• Ocular Hazard Distance: 3 m (9.84 ft)
• Ambient Luminance: 250–500 lux

14. Warranty & Support

• Device: 1 year; Remanufactured equipment: 90 days; Lamps: 90 days.
• Support: USA/Canada 1‑800‑322‑8546 • Overseas 1‑419‑636‑6304 • Email: service@daavlin.com • www.daavlin.com

15. Downloadable Resources

• ClearLink™ 1 Series Operation Manual (PDF) – add your site link
• DT 1 Series Operation Manual (PDF) – add your site link
• Treatment Time Calculator
• Treatment Log Sheet (PDF) – optional